Single Phase (1PH) Load

CD3000S 1PH – From 10A to 90A

CD3000S 1PH


Technical Specification
  • Voltage power supply: 24V min, 480V Max, 600V on request
  • Input Signal: SSR , Analog 4÷20mA and 0÷10V is available as an option on units from 15A÷90A included
  • Firing: Zero crossing ZC / Burst Firing
  • Fan Voltage: Supply 230V ± 15% (110V is available as an option)
  • Heater Break Alarm: Discrimination better than 20%. * Circuit microprocessor based to diagnose partial or total load failure and short circuit on Thyristor. * Latching alarm plus reset. * Relay output 1A at 230V. * Automatic calibration of one or more unit at the same time using a dedicated digital input or using for each unit the calibration button.
  • Approvals: EMC; cULus available as an option on basic units
  • Mounting: Din rail mounting up to 90A included, bulkhead over 110A, IP20 protection
  • Operating Temperature: 0÷40° up to 90A included (for higher temperature see the derating curve)

REVEX 1PH – The Power Controller On Demand

REVEX 1PH


Technical Specification
  • Load type: Normal Resistance, Infrared Short, Medium and Long, Transformer Primary, Cold resistance and SiC elements
  • Inputs: 4:20mA, 0:10V, SSR and ModBus as std.
  • Firing mode: Half Cycle, Single Cycle, Burst Firing, Delayed Triggering, Phase Angle with or without Soft Start
  • Control Mode: Voltage, Current and Power or V2 and I2 with additional Transfer to VxI
  • Communication: RS485 port. RTU Modbus® Protocol
  • USB: Port integrated for configuration in safety mode (No Load and Auxiliary Voltage needed) Unit Powered Through USB
  • Approvals: Comply with EMC
  • Dual Current Limit: For peak and RMS value
Option
  • All options are shown below with the relevant model code
  • HB Alarm to diagnose partial or Total Load Failure and Thyristor Short Circuit

REVO C 1PH – Revo Connect Universal SCR Power Controller Single Phase

Schema di collegamento del REVO C monofase

REVO C 1PH


  • Phases: 1
  • Current Range form 30 to 2100A.
  • Voltage Range 480V, 600V and 690V .
  • Inputs: 4:20mA , 0:10V, SSR and ModBus as std and different Field Bus Listed in the Product Coding
  • Firing mode: Half Cycle, Single Cycle, Burst Firing, Delayed Triggering, Phase Angle with or without Soft Start
  • Control Mode: Voltage, Current and Power or V2 and I2 with additional Transfer to VxI
  • USB: port integrated for configuration in safety mode (No Load and Auxiliary Voltage needed) Unit Powered Through USB
  • 100 KA: Short Circuit Current rating (SCCR) up to 600V
  • cUL / UL and CE + EMC approved

REVO S 1PH Thyristor Power Controller

REVO S 1PH


  • From 30 up to 800A
  • Voltage Range 480V, 600V and 690V
  • Load type: Resistance, IR Lamp long and medium waveform
  • Inputs: SSR Std, 0:10V, 4:20mA and Heather Break alarm are options
  • Firing mode: Zero Crossing, Burst Firing available with analogue input only



REVO SSR ANALOG | 0:10V & 4:20mA Input SSR

REVO SSR ANALOG | 0:10V & 4:20mA Input SSR


  • Rating 0:62; 0:74 and 0:90
  • Max. voltage 480V or 600V AC as option
  • Load type: Resistance, IR Lamp long and medium waveform
  • Inputs: 0:10V, 4:20mA and Heather Break alarm are options
  • Firing mode: Burst Firing

REVO Sx | Multiple Low Power Solid State Relay

REVO Sx - Multiple Low Power Solid State Relay


  • From 3.5 up to 7A
  • Max. voltage 240V or 480V AC as option
  • Load type: Resistance, IR Lamp long and medium waveform
  • Inputs: SSR Std
  • Firing mode: Zero Crossing

REVO SSR Long Life Solid State Relay

REVO SSR Long Life Solid State Relay


  • Range: 0:62; 0:7; 0:90
  • Max. voltage 480V or 600V AC as option
  • Load type: Resistance
  • Inputs: SSR Std, 0:10V, 4:20mA and Heather Break alarm are options
  • Firing mode: Zero Crossing

REVO TC 1PH Temperature and Power Controller

REVO TC 1PH


  • Suitable for Normal Resistance load types
  • From 30A to 210A
  • Max. voltage 480V, 600Vac
  • Load type: Resistance
  • Inputs: Pt100, Thermo Couple, 0:10V, 4:20mA
  • Heather Break alarm options
  • Firing mode: Zero Crossing

Revo PN – Suitable to control Electric Heaters and IR Lamps in Industrial Heating Systems

REVO PN


  • Modules of 12 or 24 zones already divided into three phases or one phase from 4 to 24 zones
  • Logic input SSR 7 ÷ 30Vdc 9mA Max (ON ≥7Vdc OFF < 6Vdc)
  • L1 - L2 - L3 Power Input 370 - 480V
  • Nominal current in continuous service Max 25A for each load
  • Max peak current (10ms) 700A
  • Nominal Voltage range Ue 24 - 600V
  • Isolation Voltage Ui 2500Vac
  • N° 8 out SSR + CT input Option T digit 16 on ordring code

Copyright © 2010 Cd Automation S.r.l. - Via P.Picasso 34/36, Legnano, MI - Tel: +39 0331 577479 - Fax: +39 0331 579479 - - PIVA:IT08925720156 - Tribunale di Milano REA:1255303 - Capitale sociale:€ 26.000,00 - All Rights Reserved.
ASK FOR INFORMATION AND QUOTATION
| Informativa Privacy | Informativa Cookie |
Diritti Interessati | Impostazioni Cookie |