Select Your Thyristor Power Controller Application and Connection

Thyristor Power Controller
CD Automation offer a wide range of products for the control of the power by Thyristor (SCR Power Controller)
  • Save money because there are small steps in nominal current rating with 27 sizes from 10A to 2600 A.
  • Innovative product range using digital technology also on small units (15 A).
  • RS485 communication with modbus protocol standard on all families with exclusion of CD3000S.
  • Configuration semplicity via Frontal KeyPad, external KeyPad or portable PC.
  • Possibility to download the suggested software configuration clicking on your application.
  • Universal Thyristor where is possible to configure all inputs types, firing modes and feedback.
  • All informations are available on our Web Site download page, where you can find Sales literature, Maintenance Manuals, Configuration software and possibility to ask for enquires.
  • Very efficient Help Desk to solve application problems. Call us and you will speak directly with our R&D team.
  • Remote service via Internet.
CD3000S 1PH – From 10A to 90A

CD3000S 1PH


Technical Specification
  • Voltage power supply: 24V min, 480V Max, 600V on request
  • Input Signal: SSR , Analog 4÷20mA and 0÷10V is available as an option on units from 15A÷90A included
  • Firing: Zero crossing ZC / Burst Firing
  • Fan Voltage: Supply 230V ± 15% (110V is available as an option)
  • Heater Break Alarm: Discrimination better than 20%. * Circuit microprocessor based to diagnose partial or total load failure and short circuit on Thyristor. * Latching alarm plus reset. * Relay output 1A at 230V. * Automatic calibration of one or more unit at the same time using a dedicated digital input or using for each unit the calibration button.
  • Approvals: EMC; cULus available as an option on basic units
  • Mounting: Din rail mounting up to 90A included, bulkhead over 110A, IP20 protection
  • Operating Temperature: 0÷40° up to 90A included (for higher temperature see the derating curve)

CD3000S 2PH – From 10A to 90A

CD3000S 2PH


Technical Specification
  • Voltage power supply: 24V min, 480V Max, 600V on request
  • Input Signal: SSR (OFF state <1Vdc ON = 4÷30 Vdc) is standard up to 90A included. Analog input 4÷20mA and 0÷10V is available from 35A (included) to 90A (included)
  • Firing: Zero crossing ZC; Burst Firing 4/8/16 with 4÷20mA or 0÷10V with 12÷24V aux. power supply.
  • Fan Voltage: 230V ± 15% standard f(110V on request opt., if current ≥75A).
  • Heater Break Alarm: Discrimination better than 20%. * Circuit microprocessor based to diagnose partial or total load failure and short circuit on Thyristor. * Latching alarm plus reset. * Relay output 1A at 230V. * Automatic calibration of one or more unit at the same time using a dedicated digital input or using for each unit the calibration button.
  • Approvals: Comply with EMC; cULus available as an option on basic units.
  • Mounting: Din rail mounting up to 90A included.
  • Operating Temperature: 0÷40° up to 90A included (for higher temperature see the derating curve)

CD3000S 3PH – From 15A to 90A

CD3000S 3PH


Technical Specification
  • Voltage power supply: 24V min, 480V Max, 600V on request
  • Input Signal: SSR (OFF state <1Vdc ON = 4÷30 Vdc) firing.
  • Firing: Zero crossing ZC.
  • Auxiliary Voltage Supply: 10Va power consumption.
  • Fan Voltage: 230V ± 15%.
  • Approvals:Comply with EMC; cULus available as an option.
  • Mounting: Din rail mounting up to 90A.
  • Operating Temperature: 0÷40° up to 90A included (for higher temperature see the derating curve)

REVEX 1PH – The Power Controller On Demand

REVEX 1PH


Technical Specification
  • Load type: Normal Resistance, Infrared Short, Medium and Long, Transformer Primary, Cold resistance and SiC elements
  • Inputs: 4:20mA, 0:10V, SSR and ModBus as std.
  • Firing mode: Half Cycle, Single Cycle, Burst Firing, Delayed Triggering, Phase Angle with or without Soft Start
  • Control Mode: Voltage, Current and Power or V2 and I2 with additional Transfer to VxI
  • Communication: RS485 port. RTU Modbus® Protocol
  • USB: Port integrated for configuration in safety mode (No Load and Auxiliary Voltage needed) Unit Powered Through USB
  • Approvals: Comply with EMC
  • Dual Current Limit: For peak and RMS value
Option
  • All options are shown below with the relevant model code
  • HB Alarm to diagnose partial or Total Load Failure and Thyristor Short Circuit

REVEX 2PH – The Power Controller On Demand

REVEX 2PH


Technical Specification
  • Load type: Normal Resistance, Infrared Short, Medium and Long waveform
  • Inputs: 4:20mA, 0:10V, SSR and ModBus as std.
  • Firing mode: Burst Firing, Zero Crossing
  • Control Mode: Voltage, Current and Power or V2 and I2
  • Communication: RS485 port. RTU Modbus® Protocol
  • USB: Port integrated for configuration in safety mode (No Load and Auxiliary Voltage needed) Unit Powered Through USB
  • Approvals: Comply with EMC
  • Dual Current Limit: For peak and RMS value
Option
  • All options are shown below with the relevant model code
  • HB Alarm to diagnose partial or Total Load Failure and Thyristor Short Circuit

REVEX 3PH – The Power Controller On Demand

REVEX 3PH


Technical Specification
  • Load type: Normal Resistance, Infrared Short, Medium and Long Waveform
  • Inputs: 4:20mA, 0:10V, SSR and ModBus as std.
  • Firing mode: Burst Firing, Zero Crossing
  • Control Mode: Voltage, Current and Power or V2 and I2 with additional Transfer to VxI
  • Communication: RS485 port. RTU Modbus® Protocol
  • USB: Port integrated for configuration in safety mode (No Load and Auxiliary Voltage needed) Unit Powered Through USB
  • Approvals: Comply with EMC
  • Dual Current Limit: For peak and RMS value
Option
  • All options are shown below with the relevant model code
  • HB Alarm to diagnose partial or Total Load Failure and Thyristor Short Circuit

REVO C 1PH – Revo Connect Universal SCR Power Controller Single Phase

Schema di collegamento del REVO C monofase

REVO C 1PH


  • Phases: 1
  • Current Range form 30 to 2100A.
  • Voltage Range 480V, 600V and 690V .
  • Inputs: 4:20mA , 0:10V, SSR and ModBus as std and different Field Bus Listed in the Product Coding
  • Firing mode: Half Cycle, Single Cycle, Burst Firing, Delayed Triggering, Phase Angle with or without Soft Start
  • Control Mode: Voltage, Current and Power or V2 and I2 with additional Transfer to VxI
  • USB: port integrated for configuration in safety mode (No Load and Auxiliary Voltage needed) Unit Powered Through USB
  • 100 KA: Short Circuit Current rating (SCCR) up to 600V
  • cUL / UL and CE + EMC approved

REVO C 2PH – Revo Connect Universal SCR Power Controller Two Phases

Schema di collegamento del REVO C bifase

REVO C 2PH


  • Phases: 2
  • Current Range from 30 to 2100A.
  • Range di tensione 480V, 600V & 690V.
  • Inputs: 4:20mA , 0:10V, SSR and ModBus as std and different Field Bus Listed in the Product Coding
  • Load type: Normal Resistance, Infrared Short, Medium and Long, Transformar Primary using Delayed Triggering
  • Firing mode: Burst Firing , Zero Crossing.
  • USB: port integrated for configuration in safety mode (No Load and Auxiliary Voltage needed) Unit Powered Through USB
  • 100 KA: Short Circuit Current rating (SCCR) up to 600V
  • cUL / UL and CE + EMC approved

REVO C 3PH – Revo Connect Universal SCR Power Controller Three Phases

Schema di collegamento del REVO C trifase

REVO C 3PH


  • Phases: 3
  • Current Range form 30 to 2100A.
  • Voltage Range 480V, 600V and 690V.
  • Inputs: 4:20mA , 0:10V, SSR and ModBus as std and different Field Bus Listed in the Product Coding
  • Firing mode:Burst Firing , Delayed Triggering and Phase Angle with or without Soft Start
  • Control Mode: Voltage,Current and Power or V2 and I2 with additional Transfer to VxI
  • USB: port integrated for configuration in safety mode (No Load and Auxiliary Voltage needed) Unit Powered Through USB
  • 100 KA: Short Circuit Current rating (SCCR) up to 600V
  • cUL / UL and CE + EMC approved

REVO S 1PH Thyristor Power Controller

REVO S 1PH


  • From 30 up to 800A
  • Voltage Range 480V, 600V and 690V
  • Load type: Resistance, IR Lamp long and medium waveform
  • Inputs: SSR Std, 0:10V, 4:20mA and Heather Break alarm are options
  • Firing mode: Zero Crossing, Burst Firing available with analogue input only



REVO S 2PH Thyristor Power Controller

REVO S 2PH


  • From 30 up to 800A
  • Voltage range 480V, 600V and 690V
  • Load type: Resistance, IR Lamp long and medium waveform
  • Inputs: SSR Std, 0:10V, 4:20mA and Heather Break alarm are options
  • Firing mode: Zero Crossing, Burst Firing available with analogue input only

REVO S 3PH Thyristor Power Controller

REVO S 3PH


  • From 30 up to 800A
  • Voltage Range 480V, 600V and 690V
  • Load type: Resistance, IR Lamp long and medium waveform
  • Inputs: SSR Std, 0:10V, 4:20mA and Heather Break alarm are options
  • Firing mode: Zero Crossing, Burst Firing available with analogue input only



REVO SSR ANALOG | 0:10V & 4:20mA Input SSR

REVO SSR ANALOG | 0:10V & 4:20mA Input SSR


  • Rating 0:62; 0:74 and 0:90
  • Max. voltage 480V or 600V AC as option
  • Load type: Resistance, IR Lamp long and medium waveform
  • Inputs: 0:10V, 4:20mA and Heather Break alarm are options
  • Firing mode: Burst Firing

REVO Sx | Multiple Low Power Solid State Relay

REVO Sx - Multiple Low Power Solid State Relay


  • From 3.5 up to 7A
  • Max. voltage 240V or 480V AC as option
  • Load type: Resistance, IR Lamp long and medium waveform
  • Inputs: SSR Std
  • Firing mode: Zero Crossing

REVO SSR Long Life Solid State Relay

REVO SSR Long Life Solid State Relay


  • Range: 0:62; 0:7; 0:90
  • Max. voltage 480V or 600V AC as option
  • Load type: Resistance
  • Inputs: SSR Std, 0:10V, 4:20mA and Heather Break alarm are options
  • Firing mode: Zero Crossing

REVO TC 1PH Temperature and Power Controller

REVO TC 1PH


  • Suitable for Normal Resistance load types
  • From 30A to 210A
  • Max. voltage 480V, 600Vac
  • Load type: Resistance
  • Inputs: Pt100, Thermo Couple, 0:10V, 4:20mA
  • Heather Break alarm options
  • Firing mode: Zero Crossing

REVO TC 2PH Temperature and Power Controller PID

REVO TC 2PH


  • Suitable for Normal Resistance
  • Three Phase 2PH (2-Leg) From 30A to 210A
  • Max. voltage 480V, 600Vac
  • Load type: Resistance
  • Inputs: Pt100, Thermo Couple, 0:10V, 4:20mA
  • Heather Break alarm options
  • Firing mode: Zero Crossing

REVO TC 3PH – Temperature and Power Controller 3PH

REVO TC 3PH


  • Suitable for Normal Resistance
  • Three Phase 3PH (3-Leg) From 30A to 210A
  • Max. voltage 480V, 600Vac
  • Load type: Resistance
  • Inputs: Pt100, Thermo Couple, 0:10V, 4:20mA
  • Heather Break alarm options
  • Firing mode: Zero Crossing

Revo PN – Suitable to control Electric Heaters and IR Lamps in Industrial Heating Systems

REVO PN


  • Modules of 12 or 24 zones already divided into three phases or one phase from 4 to 24 zones
  • Logic input SSR 7 ÷ 30Vdc 9mA Max (ON ≥7Vdc OFF < 6Vdc)
  • L1 - L2 - L3 Power Input 370 - 480V
  • Nominal current in continuous service Max 25A for each load
  • Max peak current (10ms) 700A
  • Nominal Voltage range Ue 24 - 600V
  • Isolation Voltage Ui 2500Vac
  • N° 8 out SSR + CT input Option T digit 16 on ordring code

Heat sink for solid state relay ssr

  • Single and Multiple Installation
  • Space reduction
  • Pre wired solution

Copyright © 2010 Cd Automation S.r.l. - Via P.Picasso 34/36, Legnano, MI - Tel: +39 0331 577479 - Fax: +39 0331 579479 - - PIVA:IT08925720156 - Tribunale di Milano REA:1255303 - Capitale sociale:€ 26.000,00 - All Rights Reserved.
ASK FOR INFORMATION AND QUOTATION
| Informativa Privacy | Informativa Cookie |
Diritti Interessati | Impostazioni Cookie |