REDUCE WIRING AND SPACE COST

Have you ever considered the Impact of Wiring and Labour Installation Costs on the value your project?

Revo-Tc-link

Well We have and it could be halved:
  • eliminating wires:
  • cut
  • number
  • stripping
  • link
  • panels to be drilled…
  • all operations that require time and will have an effect on your the final cost.
Cabinet-revo-tc
Now you can reduce costs and space with REVO TC, the innovative system of thermoregulation.
Compare the new REVO TC to a traditional system and you save:
  • 11 wires for each zone.
  • Each zone takes 11 minutes (see the diagram).
  • For each zone you save 11 wires x 11 minutes = 121 minutes in total.
  • If you use descrete controllers you also avoid the panel cutting/drilling.
  • Thats another 15 minutes per controller.
  • Thats a total time saved of 136 minutes for zone.
  • So how many zones/loops do you sell in one year?

 

DISTRIBUITED SYSTEM WITH REVO TC

Have you ever considered the Impact of Wiring and Labour Installation Costs on the value your project?

Distribuited-systems-Co-Extrusion-I
Traditional system
Today many machines adopt the traditional
system layout as shown below on the left.
Distribuited-systems-Co-Extrusion-II As can be seen, the new REVO TC distribuited hardware solution, will give crucial saving such as:

  • Number of wires (cable and labour cost).
  • Errors in wiring the machine.
  • No wire channels.
  • Cable lenght reduced by 80%.
  • Cabinet’s space reduced.Consider that each cabinet section
  • The cabinet space used is a key factor.
  • If the space of components used is doubled then the cabinet size is doubled.

 

REVO TC PHILOSOPHY

  • Labour for wiring reduced dramatically using multiple cable with connector.
  • Reduction of used space, saving cabinet cost.
  • Single loop integrity with easy local identification of the faulty zone.
  • REVO TC up to 40A is normally used for plastics machinery.
  • REVO TC over 60A in one, two and three phase versions is normally used in Furnaces.
Revo-Tc-Modularity
CONTROLLER MODULE
  • PID temperature controller with Pre Tune, Self Tune and Manual tuning
  • 3 Off PID pallets to be enabled at programmed temperature.
  • RS485 communication from 19200 to 57600 Baud Modbus RTU protocol.
  • Dual Display to read PV, Set Point and load current.
  • Auto/Manual bump less balances .
  • Universal input for Thermocouples, RTD and linear Signal.
  • Four configurable outputs Relay, SSR, 4:20mA and 0:10V.
  • Cooling Output selection for Water, Oil or Ventilation.
  • Programming port USB with CD Automation programming cable.
THYRISTOR MODULE
  • Solid State Relay
  • Fuse & Fuse Holder
  • Current Transformer
  • Heatsink
  • Din Rail Mounting
  • Indication LED

 

Select one of the Below Models:

REVO TC 1PH Temperature and Power Controller

  • Suitable for Normal Resistance load types
  • From 30A to 210A
  • Max. voltage 480V, 600Vac
  • Load type: Resistance
  • Inputs: Pt100, Thermo Couple, 0:10V, 4:20mA
  • Heather Break alarm options
  • Firing mode: Zero Crossing

REVO TC 2PH Temperature and Power Controller

  • Suitable for Normal Resistance
  • Three Phase 2PH (2-Leg) From 30A to 210A
  • Max. voltage 480V, 600Vac
  • Load type: Resistance
  • Inputs: Pt100, Thermo Couple, 0:10V, 4:20mA
  • Heather Break alarm options
  • Firing mode: Zero Crossing

REVO TC 3PH Temperature and Power Controller

  • Suitable for Normal Resistance
  • Three Phase 3PH (3-Leg) From 30A to 210A
  • Max. voltage 480V, 600Vac
  • Load type: Resistance
  • Inputs: Pt100, Thermo Couple, 0:10V, 4:20mA
  • Heather Break alarm options
  • Firing mode: Zero Crossing

Informativa Privacy | Informativa Cookie | Impostazioni Cookie